PVC identification method

Sep 28, 2019|

Shenzhen Shenchuang Hi-tech Electronics Co., Ltd(SChitec) is a high tech enterprise which specialized in phone accessories production and sales. Our main products include travel chargers, car chargers, USB cables, power banks and other digital products.All products are safe and reliable, with unique styles.products pass certificates like CE,FCC,ROHS,UL,PSE,C-Tick,etc,  If you are interested in, you can contact ceo@schitec.com directly.

 

Stay Charging Safely with SChitec

PVC identification method PVC identification method

The conventional PVC identification methods are generally classified into the following three categories, namely:

(1) Identification of combustion method:

Softening or melting temperature range: 75~90 °C;

Combustion condition: self-extinguishing after ignition;

Burning flame state: there is smoke on the yellow and green; after the fire: off from the fire; smell: irritating sour.

This method is the easiest and straightforward and is generally preferred.

(2) Solvent treatment identification:

Solvent: tetrahydrofuran, cyclohexanone, ketone, dimethylformamide;

Non-solvent: methanol, acetone, heptane.

By adding suspected PVC plastic to the above solvent, observe the dissolution of the plastic to determine whether it is PVC. After the solvent is heated, the dissolution effect will be more pronounced.

(3) Specific gravity method:

The specific gravity of PVC is 1.35~1.45, which is generally around 1.38. Polyvinyl chloride and other plastics can be distinguished by differences in specific gravity or by specific gravity. However, because PVC can add plasticizers, modifiers and fillers, the PVC becomes very different in specific gravity, and the difference between soft and hard is great. At the same time, many properties of PVC plastics are changed due to the addition of some components, resulting in The commonly used identification method is not effective, and even the phenomenon changes, and it is impossible to make an accurate judgment. For example, in terms of density, plasticized polyvinyl chloride (about 40% plasticizer) is 1.19~1.35; while PVC hard products are increased to 1.38~1.50. In the case of highly filled PVC products, the density sometimes exceeds 2.

In addition, it can also be determined by measuring whether or not chlorine is contained in the material, but since vinyl chloride copolymer, neoprene, polyvinylidene chloride, chlorinated polyvinyl chloride, etc. all contain a relatively high proportion of chlorine, color development by pyridine is also required. Reaction to identify. Note that before the test, the sample must be extracted with diethyl ether to remove the plasticizer. Test method: The sample taken with diethylbenzene is dissolved in tetrahydrofuran, the insoluble component is filtered off, and methanol is added to precipitate it. Dry below the degree. A small amount of dried sample was reacted with 1 ml of pyridine. After a few minutes, 2 to 5% sodium hydroxide in methanol (1 g of sodium hydroxide dissolved in 20 ml of methanol) was added, and the color was observed immediately, 5 min. And observe again after 1h. Different chlorine-containing plastics can be identified based on color.

In daily life, the more contact you need to distinguish between PVC and PE plastic film (bag), simple method:

(1) Touch method

It feels lubricated by hand, and the surface is coated with a layer of wax (chemically called waxy), which is a non-toxic polyethylene film bag, while the polyvinyl chloride film is somewhat sticky to the touch.

(2) dithering method

The hand is shaken, the sound is brittle, and the quality is easy to float is a polyethylene film bag. The low-pitched sound is a polyvinyl chloride film bag.

(3) Combustion method

It is flammable in case of fire, the flame is yellow, there is paraffin-like oil dripping when burning, and there is a gas when the candle burns. It is a non-toxic polyethylene film bag. If it is not easy to burn, it will be extinguished when it leaves the fire. The flame is green and it is a PVC film bag.

(4) Water immersion method

After immersing the plastic bag in water and pressing it into the water, the polyethylene that can float out of the water surface is polyvinyl chloride (the density of polyethylene is less than water, and the density of polyvinyl chloride is greater than water; respectively, at room temperature is about 0.92 g/cm3 and 1.4 g/cm3).

It is also possible to take a copper wire and burn it red in a fire. Then, the copper wire is brought into contact with the test plastic film to cause a chemical change, and the copper wire with the plastic component is put back into the flame. At this time, it is necessary to observe carefully. If there is a colorful and dazzling green flame, it means that the plastic material contains chlorine and belongs to the polyvinyl chloride material.

 


← Previous: PVC synthetic material
Next: Power Transformers →
Send Inquiry