Opticalcoupler equipment type
Nov 15, 2019|
Stay Charging Safely with Schitec
Opticalcoupler equipment type
There are two types of opticalcoupler equipments: one is a nonlinear opticalcoupler equipment and the other is a linear opticalcoupler equipment.
The current transfer characteristic of a nonlinear opticalcoupler equipment is non-linear. This type of opticalcoupler equipment is suitable for the transmission of switching signals and is not suitable for transmitting analog quantities. The commonly used 4N series opticalcoupler equipments are nonlinear opticalcoupler equipments.
The current transfer characteristic curve of the linear opticalcoupler equipment is close to a straight line, and the performance is good when the signal is small, and the isolation can be controlled by the linear characteristic. A commonly used linear opticalcoupler equipment is the PC817A-C series.
The commonly used opticalcoupler equipments in switching power supplies are linear opticalcoupler equipments. If a nonlinear opticalcoupler equipment is used, it is possible to deteriorate the oscillation waveform, and in severe cases, parasitic oscillation occurs, so that the oscillation frequency of several kilohertz is sequentially modulated by the low-frequency oscillation of several tens to hundreds of Hz. The result is that color TV, color display, VCD, DCD, etc. will cause interference on the image screen. At the same time, the power supply has a reduced load capacity. In the maintenance of switching power supply such as color TV, display, etc., if the opticalcoupler equipment is damaged, it must be replaced by a linear opticalcoupler equipment. The commonly used 4-pin linear opticalcoupler equipment is PC817A----C. Commonly used six-leg linear opticalcoupler equipments such as PC111 TLP521 are: LP632 TLP532 PC614 PC714 PS2031 and so on. The commonly used 4N25 4N26 4N35 4N36 is not suitable for use in switching power supplies because these four opticalcoupler equipments are nonlinear opticalcoupler equipments.
Due to the variety and types of opticalcoupler equipments, there are more than a thousand models in the Optoelectronics DATA Handbook, which can usually be classified as follows:
(1) According to the optical path, it can be divided into an external optical path photocoupler (also known as a photoelectric intermittent detector) and an internal optical path photocoupler. The external optical path photocoupler is further divided into a transmissive type and a reflective type photocoupler.
(2) According to the output form, it can be divided into:
a, photosensitive device output type, including photodiode output type, phototransistor output type, photocell output type, optical thyristor output type.
b, NPN triode output type, including AC input type, DC input type, complementary output type.
c. Darlington triode output type, including AC input type and DC input type.
d, logic gate circuit output type, including gate output type, Schmitt trigger output type, three-state gate output type.
e, low conduction output type (output low level of millivolts).
f, optical switch output type (on-resistance is less than 10Ω).
g, power output type (output such as IGBT/MOSFET).
h, Photosensitive resistor type (through light, control output resistance, output resistance can be bidirectional, can be exchanged, change the inconvenience of only one direction such as PC817, pure resistance material, non-polar output, such as LCR-0202)
(3) According to the package form, it can be divided into coaxial type, dual in-line type, TO package type, flat package type, chip package type, and optical fiber transmission type.
(4) According to the transmission signal, it can be divided into digital opticalcoupler equipment (OC gate output type, totem pole output type and tri-state gate circuit output type, etc.) and linear opticalcoupler equipment (can be divided into low drift type, high linear type, Broadband type, single power type, dual power type, etc.).
(5) According to the speed, it can be divided into low-speed photocoupler (phototransistor, photocell and other output type) and high-speed opticalcoupler equipment (photodiode with signal processing circuit or photosensitive integrated circuit output type).
(6) According to the channel, it can be divided into single-channel, dual-channel and multi-channel opticalcoupler equipments.
(7) According to the isolation characteristics, it can be divided into common isolation opticalcoupler equipments (general optical glue potting is less than 5000V, air seal is less than 2000V) and high voltage isolation opticalcoupler equipment (can be divided into 10kV, 20kV, 30kV, etc.).
(8) According to the working voltage, it can be divided into low power supply voltage type photocoupler (generally 5~15V) and high power supply voltage type photocoupler (generally greater than 30V).


