Common types of cable accessories
Nov 27, 2019| Shenzhen Shenchuang Hi-tech Electronics Co., Ltd(SChitec) is a high tech enterprise which specialized in phone accessories production and sales. Our main products include travel chargers, car chargers, USB cables, power banks and other digital products.All products are safe and reliable, with unique styles.products pass certificates like CE,FCC,ROHS,UL,PSE,C-Tick,etc, If you are interested in, you can contact ceo@schitec.com directly.
Stay Charging Safely with SChitec
Common types of cable accessories
Heat shrinkable
There are many kinds of products used in the middle and low voltage cable accessories, such as heat shrinkable accessories, prefabricated accessories and cold shrinkable accessories. They have the following characteristics:
Generally, the materials used are blends of polyethylene, ethylene vinyl acetate (EVA) and ethylene propylene rubber. This kind of products mainly use stress tube to deal with the problem of electrical stress concentration. In other words, the parameter control method is used to relieve the stress concentration of electric field. The main advantages are light, easy to install, good performance and low price. The stress tube is a kind of heat shrinkable tube with special electrical parameters, which has moderate volume resistivity (1010-1012 Ω cm) and large dielectric constant (20-25). The electrical parameters are used to force the stress at the cable insulation shielding fracture to disperse into a more uniform distribution along the stress tube. This technology is generally used in 35kV and below cable accessories. Because the stress tube will heat up when the voltage level is high, it can not work reliably.
The key technical problems in its use are:
To ensure that the electrical parameters of the stress tube can work reliably, they must reach the values specified in the above standards. In addition, it is necessary to fill the air gap of the cable insulation semi conducting layer fracture with silicone grease to eliminate the gas and reduce the partial discharge. Due to the poor internal stress treatment, the crosslinked cable will shrink greatly during operation. Therefore, when installing accessories, pay attention to the overlap of stress tube and insulation shield not less than 20 mm, so as to prevent the separation of stress tube and insulation shield during shrinkage. Due to the small elasticity of the heat shrinkable accessories, air gap may be generated at the interface during the thermal expansion and cold contraction during operation, so the sealing technology is very important to prevent moisture immersion.
Prefabricated
The materials used are generally silicone rubber or ethylene propylene rubber. In this paper, the geometric structure method, stress cone, is used to deal with the problem of stress concentration. Its main advantages are excellent material performance, easier and faster installation, installation without heating, good elasticity, making the interface performance greatly improved. The main forms of medium and low voltage and high voltage cables. The disadvantages lie in the high requirements for the outer diameter of the insulation layer of the cable. The usual interference is 2-5mm (that is, the outer diameter of the cable insulation is larger than the inner hole diameter of the cable accessories). If the interference is too small, the cable accessories will fail; if the interference is too large, the installation of the cable accessories is very difficult (high process requirements). Especially in the middle and indirect head, the problem is prominent, the installation is not convenient, and often become a failure point. In addition, the price is more expensive. The key technical problems in its use are:
The size of accessories and the size of cables to be installed shall meet the specified requirements. In addition, silicone grease is also required to lubricate the interface for easy installation.
Cold shrinkage type
Cold shrinkable cable accessories are parts of various cable accessories, which are made of elastomer materials (commonly including silicone rubber and ethylene propylene rubber) by injection molding in the factory, then expanded and lined with plastic spiral supports. During field installation, these pre expansion parts are sheathed at the end or joint of the treated cable, the plastic spiral strip (support) which is internally supported is pulled out, and the cable accessories formed by pressing on the cable insulation are compressed. Because it relies on the elastic retraction force at room temperature, rather than the heat shrinkable cable accessories that need to be shrunk by fire, it is commonly known as the cold shrinkable cable accessories. In the early stage, the cold shrinkable cable terminal only used the silicon rubber cold shrinkable part for the additional insulation, and the stress cone type or stress band wrapped type was still used for the electric field treatment. The cold shrinkage stress control tube is widely used, and the voltage level is from 10kV to 35kV. For cold shrinkable cable joints, cold shrinkable insulating pipes are used as reinforced insulation for 1kV level, and cold shrinkable insulating parts with inner and outer semi conducting shielding layers are used for 10kV level. Cold shrink branch sleeve shall be used at the fork of three core cable terminal.
Cold shrinkable cable accessories have the advantages of small size, convenient operation, rapidity, no need of special tools, wide application range and less product specifications. Compared with heat shrinkable cable accessories, it does not need to be heated by fire, and after installation, moving or bending will not cause the risk of interlayer separation of accessories like heat shrinkable cable accessories (because the cold shrinkable cable accessories rely on elastic compression force). Compared with prefabricated cable accessories, although the internal interface characteristics are guaranteed by elastic compression force, it does not correspond to the cable section one by one like prefabricated cable accessories, with many specifications.
It must be pointed out that before installation on the cable, the components of prefabricated cable accessories have no tension, while the components of cold shrinkable cable accessories are under high tension. Therefore, it must be ensured that during the storage period, the cold shrinkable components should not have obvious permanent deformation or elastic stress relaxation, otherwise, after installation on the cable, it cannot be guaranteed that there is enough elastic compression force, so it is not necessary to Good interface characteristics can be guaranteed.


